Home > Error Code > F06 Error Code Whirlpool Duet Washer

F06 Error Code Whirlpool Duet Washer

Contents

if the wiring connections are okay, i recommend that you check the resistance of the motor windings. Just replaced MCU with new (not refurbished) one. Leave a Reply Click here to cancel reply. This means the control is unable to properly detect motor speed and the machine will shut down. check over here

Top Load Washer - White See Details Related Pages Kenmore 5M followers Follow Washers 1K followers Follow Not only Santa needs a listSave gift ideas to your "Gift List" catalog Sweeps The diagnostic test works from C01-C08 with no problems. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & See Details More Products Kenmore 28133 5.3 cu.

F06 Error Code Whirlpool Duet Washer

Top-Load Washer ... My door lock works fine and my drain pump is clean. If all checks ok, then its either a faulty MCU, or faulty drive motor. In other words if I replaced our CCU and the problem wasn't resolved could I put my original part back and return/exchange the new CCU for the next part (MCU then

  • What do you recomend to me to check or replace the module.
  • Still getting F06 March 15 by Phat Bastard Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?
  • Cancel Terry Rep: 1 Posted: 09/24/2012 Options Permalink History Thank you very much.
  • another problem that could cause the error code to be displayed intermittently would be a loose wire harness connection that is affected by vibration when the washer is spinning at high
  • Cancel Axel Rep: 13 1 Posted: 08/31/2015 Options Permalink History If you wonder whether the tachometer built into the motor is working, consider doing the following: At the MCU, separate the
  • Was this answer helpful?

Include every digit in the model number, even if some are sized or styled differently. Bill Newberry 713,578 views 10:43 whirlpool awe 6730/P- Program serwisowy - Duration: 4:29. Earned 137,351 community points in Click'>Kenmore April 2nd, 2009 Answered in 5 hours Comment Give your feedback by voting on answers 0 votes Didn't find what you are looking for? F06 Error Code On Maytag Washer Check the wiring diagram Perform a continuity check of the Drive Motor windings.

They undergo quite a lot of friction, and after a while wear out. F6 Error Code Kenmore Washer Was this answer helpful? I am not aware of the F06 code being caused by a problem with the user interface control board.

Come git you one.

I replaced the bearings which were obviously bad, the washer sounded like a jet taking off. F06 Error Code Apc See Details Kenmore 22332 3.5 cu. However, it must be unplugged for SEVERAL minutes. Top Load Washer ...

F6 Error Code Kenmore Washer

Add your answer Sign in to answer a question 3 Answers from these members: The "F06" fault code indicates a drive motor tachometer error. http://www.shopyourway.com/questions/1085126 CT Sat 7:00 a.m. - 9:00 p.m. F06 Error Code Whirlpool Duet Washer ft. Kenmore Elite Washer He4t Error Code F6 Yes No Voted Undo Score 4 Cancel Comments: + That's great info!

If I need to buy several parts to help me troubleshoot, what order should I install them so maybe I can return any unused parts? check my blog Don't buy a new washer. Disconnect the power (i.e., unplug the machine) and remove the three torx-head screws that hold the panel in place. I tried everything I could find on the forums and in my manual. F06 Error Code Battery Charger

you should measure about 6 ohms of resistance through each winding in the motor as shown below. I anticipate that the technician likely checked the wire harness connections between the drive motor, the motor control unit and the central control unit (main control board). Good luck--you're going to need it! this content Cancel Steve Rep: 1 Posted: 10/25/2014 Options Permalink History I did alot of messing around with connectors and all that.

Connector 1 - is the serial communications link between the MCU and CCU and has three wires. Kenmore Microwave F6 Error Code I was hoping to make it to 15, but I am not complaining. :) Was this answer helpful? I am confident that they can address your service concerns. If the washer gets to a point where the F06 is occurring constantly, the washer should be able to accurately diagnosed

Yes No Voted Undo Score 1 Cancel Comments: Old Turkey - yes I did download the service manual.

how-2-repair.com 24,359 views 8:24 Kenmore Elite HE3T Washer F6 code.....WHAT THE F! - Duration: 5:06. 116falconer 5,116 views 5:06 Loading more suggestions... If you find no problem with the relays, it's possible there is other damage to the control unit, or to the wires between the control unit and the various devices. It will flash the F06 error code in the display. F06 Error Code Hotpoint Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit.

Offer valid for online purchases only. Posted July 11, 2013 Answers Yadira B, July 11, 2013 appliance error codes can be confusing. how-2-repair.com 158 viewsNew 9:09 Samsung washing machine error code 4E and E1 Fault Not filling in allocated time - Duration: 8:55. have a peek at these guys The most suspect components that would cause this failure code are the drive motor, the motor control unit (control board) or the wire harness.