Home > Error Code > Vita Spa Pb Error Code

Vita Spa Pb Error Code

Contents

Depending on how old your tub is you may be able to find what you need there. Did you buy used or new? Logged Hot Tub Forum Re: Vita owners….pb code??? When i plug in the control panel I hear a click, then after a few seconds the jets kick on and off while the control panel is a blank screen. weblink

Cool down procedure begins. If it is the lower circuit board, I think that the only repair is replacing the circuit board.Hope this helps. One sensor has detected 110º. Only a tech in the field can diagnose to this level of failure "HL", "HiLi" or "OH" message Caused by heater overheating or bad sensor Sensor is connected to the outside additional hints

Vita Spa Pb Error Code

If that is not the issue, you may need to replace the topside control panel. ICE2 = Freeze protection. I'm not familiar with Eco-Spa at all. Now the jets have stopped working.

No humming either. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. How do you check them? Eco Spas Hot Tub Reviews Std = Spa operating in Standard Mode.

Circulation pump not working. SESH = Sensor short, nonfunctional. Show actual water temp; all seems to be in working order except for the motor will come on and then trip out internally. you can try this out All rights reserved. | Privacy Policy | Get In Touch | TeamPortal FacebookVimeoYoutubePinterestInstagram

If not then the circuit board is more than likely bad. Eco Spa Reviews By any chance is the water very cold? HOT = Circuit Board temperature has exceeded acceptable limit. Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa

  1. If you don't have a topside control then the Pb code is a malfunction with the circuit control board.
  2. PSoC = Pressure switch open with circulating pump.
  3. mhburris4040 is online now I have a L700C Vita spa with a problem code P6.

Eco Spa Hot Tub Manual

I’ll have to check and see if it’s under warranty with a dealer.Dumb Question, but can you tell what the filter would have to do with it? http://www.spadepot.com/spa-error-codes.htm I am assuming that when you unplugged it you kept it off for about 15 minutes before plugging back into the control box. Vita Spa Pb Error Code Any thoughts? Vita Spa Error Codes Hold = Panel sensors have been pressed too many times in a short period of time.

My thoughts are the heater temp sensors? have a peek at these guys Most spa repairs I do are pretty minor - I find most of what I need at www.HotTubParts.com . We hope it helps solve your problem. We are having a lot of spas not heated going into freeze protection mode immediately. Eco Spa Parts

Any advise would be appreciated. If the wire is burned it usually means the relay is bad. I do have a mineral (yellow stick with a cartridge on the end of it) stick to help keep the water PH balanced. check over here Heater is deactivated.

After replacing the cord, the motor ran for a few minutes then the pump made a clicking noise and shut off. Hot Tub Error Codes I opened the control box and noticed a few dirty connectors, so I replaced them and Bingo! Pump looks like its only running at low speed and not high speed.

Ask Your Own Pool and Spa Question Customer: replied3 years ago.

I also noticed heat damage on both receptacles, one of the pin s on the male ends was black at the bottom, and the female end has obvious heat damage as Entire system is disabled. help « Reply #4 on: March 23, 2011, 06:50:19 PM » Print Pages: [1] « previous next » Hot Tub Forum » General » Hot Tub Forum » Vita owners….pb code??? I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah

We did set it all up fine and it was working.. Contact qualified service technician. The issues listed here are ones which could be considered severe and require immediate attention especially during the Winter months where freezing becomes more of a problem. this content One sensor has detected 110º F.

I live in a single story ranch that was built in 1952. drops. Sensor plugged into jack B is not working. Ask Your Own Pool and Spa Question Expert: Poolservice123 replied3 years ago.

I would suggest turning the power off and checking the connections as suggested, unplugging them and reconnecting them. You can leave a response, or trackback from your own site. Spa has shut down. SnH Hi Limit circuit open or faulty SnS Sensors out of balance, reporting different results SnT Temperature sensor fault, circuit open or faulty SP-F1,F2 or F3 Fuse 1,2 or blown SP-HR

FL2 = Pressure switch problem. Switch closed while pump is deactivated. Eco Spa is made by DM Industries, if you do a google search for DM Industries spas you'll find a few sites that carry different parts for Eco Spa. http://www.vitaparts.com/Vita-Spa-Printed-Circuit-Boards_c14.htm Ask Your Own Pool and Spa Question Expert: Poolservice123 replied3 years ago.

Customer: Hello...let me check on that error code..Customer: I think this spa has a Balboa control pack and if so, then the P6 is an error code for the light.Customer: Are Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Simply "click" on the issue below that best suits you for instructions on how to handle.