Home > Error Code > Whirlpool Washer Error Codes F21

Whirlpool Washer Error Codes F21

Contents

If “Sud” is displayed a potential suds lock is detected. Check Pressure Switch for correct working with a DVM/VOM. 3. Unplug washer or disconnect power. 3. If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. http://discusswire.com/error-code/whirlpool-top-load-washer-error-codes.html

Check the drain hose and make sure it is not plugged or kinked. 2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check the water temperature sensor and connection to it. Lastly F9 faults are related to the washer's ability to drain. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html

Whirlpool Washer Error Codes F21

Unplug washer or disconnect power. 3. Replace User Interface if drum is rotating. 4. If door latched: A. This should clear the unit of the excess detergent. 1.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. Door switch/lock unit failure. 1. Whirlpool Top Load Washing Machine Error Codes F5 - Control Board Failure - Replace control board (clock).

Replace switch if defective. 4. NOTE: "Anytime I say unplug and check connections" or something like that... The F9E1 long drain error is referring to duration not length. If the condition continues four times, the F31 code will show. 1.

Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect Whirlpool Duet Reset Replace the Motor Control Unit. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness This should clear the unit of the excess detergent. 1.

  • F1E2 Error - Motor control fault.
  • I had so many questions and they answered them all." Sharon S.
  • Press CANCEL and observe for 1 minute to ensure operation is correct. 2.
  • MAIN RELAYS ERROR One of the main relays is not working properly.

Whirlpool Top Load Washer Error Codes

All rights reserved. http://www.appliancehelponline.com/whirlpool.html Try unplugging the Unit for two minutes to see if that fixes the error. • Check CCU. Whirlpool Washer Error Codes F21 Verify CCU operation by running a Diagnostic Test or any cycle. Whirlpool Duet Dryer Error Codes The wires should be to the left when facing the MCU connectors. 9.

Check Steamer for continuity (Abnormal =infi nity). 2. news In this case, replace control board (also called ERC or clock). If too much detergent was used: Run the unit through a RINSE/SPIN cycle. A power glitch may cause this error. Whirlpool Washing Machine Error Codes E1

NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. Close Thank you! Possible Causes/Procedure Door lock mechanism is broken or removed from door. http://discusswire.com/error-code/f02-error-code-whirlpool-washer.html This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain

F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Whirlpool Dryer Error Codes Get all the details Close 365 Day Return Policy You may return an unused and uninstalled part in its original packaging. Question about Whirlpool duet Washing Machines 1 Answer This is the second time this problem has occurred. ...F15 Motor control unit error If the MCU detects multiple resets or errors during

Press STOP/CANCEL to clear the display.

F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Press STOP/CANCEL to clear the display. The machine will drain for 3 minutes before unlocking the door. 3. Whirlpool Washer Error Codes A10 Door switch/lock unit failure. 1.

Ld Long drain "Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. Check CCU F/15 Motor Control Unit (MCU) Error If the MCU detects multiple resets or errors during a wash cycle, it will go into this error mode. Check the drain hose and make sure it is not plugged or kinked. 2. check my blog Discount will be automatically applied during check-out.

Press STOP/CANCEL to clear the display. Check the connections between the Steamer 3. F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table.If resistance is 0 Ω or infi nite value, replace NTC.

Make sure that the drive motor connections are secure. Check the MCU by looking for operations of the drive motor. 5. The unit will attempt the clean out the suds three times before displaying this error.