Home > Whirlpool Duet > Whirlpool Duet Washer Error Codes F02

Whirlpool Duet Washer Error Codes F02

If you are completely confident that you can safely access internal washer components, then you may be able to unplug the washer and check the drain pump for a clog. ft. Cleaned hoses and pump filter. Remove the filter and check the housing and pump impeller vanes for debris (see if you can move the pumps impeller by hand). this content

I removed the boot, which was a task because the hose clamp was at the back of the washer, and when I dropped the boot, hanging there was almost 2 handfuls RepairClinic.com 94,995 views 2:21 Whirlpool Duet Sport/Kenmore HE3 Dryer Disassembly – Dryer Repair Help - Duration: 4:01. just don't know Where!!) Also can you clean out the pump without disassembling the washer? I was really in a pickle!

RepairClinic.com Watch this video: Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Check the drain line for kinks or clogs. Sock and tons of lint were the culprit.

  1. Check the drain line for kinks or clogs.
  2. Click here to visit Merchant's home page.
  3. Front Load ...

So I took the pump out to check the motor by putting power to it. The author of this site has no liability for errors, omissions, or any defects whatsoever in the information or instructions, or for any damage or injury resulting from the utilization of F02 is long drain. Make sure the inner drum turns freely. (There may be some magnetic resistance (Magnetic Motor) but there should be no mechanical drag.)) (Duet Washer Motor Check) F8E0 Error - (Steam models)

Place some previously washed clothes back in the washer without adding any detergent and start the washer. Happy to help. Thanks so much again. This is a wonderful site...

ApplianceVideo.com 223,131 views 3:11 How to repair a dishwasher, not draining - troubleshoot Whirlpool - Duration: 6:18. Reply Matthew says: October 19, 2015 at 8:13 pm Awesome! Last edited by fredo008 : 07-11-2010 at 08:31 AM. #5 (permalink) 08-05-2013, 11:46 AM bouldervolt Junior Member Join Date: Aug 2013 Posts: 1 Pump access cover This thread Appliance Parts, Accessories & Repair Help.

If washer was allowed to "rest" for awhile, and drain/spin repeated, then water would drain. https://www.linkedin.com/pulse/what-does-error-code-f02-mean-whirlpool-washing-machine-zalmen-pollak I have had several of these become unplugged at the sensor connection at the back of the washer drum. (Duet Washer Temperature Sensor Check) F5E1 Error - Door switch fault. With the water already bailed from the washer you can twist the filter head counter-clockwise to remove. Find out more » Total: $134.06 Add to Cart Install Help Watch this helpful video to determine how to install your part.

Try unplugging the Unit for two minutes to see if that fixes the error. http://discusswire.com/whirlpool-duet/f01-error-whirlpool-duet-washer.html Click here to visit Merchant's home page. Any advice? Like it never happened : )Duet Washer Part Descriptions Back to Top Back to Top You May Also Like...

I can't believe they don't have that in the manual. I ran my washer machine immediately afterwards and no problem. If too much detergent was used, run the unit through a Rinse/Spin cycle, then a Normal cycle, without adding any detergent. have a peek at these guys A power glitch may cause this error.

If there is an error reading this data, it will cuse this error. Glad you found the info useful! Check mechanical linkage from dispenser motor to the top of the dispenser.

If the Duet successfully runs 10 cycles in a row with no fault the error will be cleared from the washer's memory, so any errors you see are likely new and

Trying to start a cycle when the washer door is open. (Duet Washer Door Switch Check) F5E2 Error - Door lock fault. Reply Matthew says: April 23, 2015 at 9:34 pm Awesome! Help?! Thanks all, Matt Reply Faye says: March 30, 2016 at 9:32 pm Sounds good to me, if I had a question about something I did not understand would be nice.

Reply Matthew says: October 19, 2015 at 9:22 pm Awesome. Thank you!! If you are completely confident that you can safely access internal washer components, then you may be able to unplug the washer and check the drain pump for a clog. http://discusswire.com/whirlpool-duet/what-does-5d-mean-on-a-whirlpool-duet-washer.html Wash, rinse, repeat -- works like brand new now. #7 (permalink) 02-09-2015, 12:13 PM RudyHyde Junior Member Join Date: Feb 2015 Posts: 1 Opened drain access port and

Easy peasy..thank you so much..save us a service call. Copyright © 2000-2016 ApplianceAid.com. Skip to content Sign In Join or Activate Products Departments Departments Shop Shop Explore Explore Advice Advice Rewards Rewards More More Home / Brands / Manage My Life / Questions Tells me that it is not the pump because it it getting through a cycle till end, have also checked the drain tube from washer to house… Laundry piled up… Exhausted

Reply Matthew says: October 19, 2015 at 8:19 pm You're most welcome. The consumer or reader is individually responsible for his or her use of the information supplied and uses this information at their own risk. If water is slowly filling the tub even when the washer is unplugged you need to replace the washer fill valves. If suds are present, reduce the amount of detergent and your washer will likely operate normally. It is likely pumping out okay after you let the washer sit because the suds turn

Put your Duet washer through the UI Tests, and check all of the connections to the control. F1, F2, F6 Are main control and program faults. Your Duet washer has detected a load during a washer cleaning cycle. Matt Reply russ says: September 18, 2015 at 6:13 pm This solved the problem!!

ft. One punctured it, causing a leak. I ran through all the steps you listed too, to no avail until the pressure switch vacuume tube was unclogged. You may find debris or objects in this area that are preventing the washer from draining properly.

The drain/filter/pump is right in front.